Skip to content
First Cast Fishing
  • Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack9 photos
  • Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack, photo 2 of 9
  • Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack, photo 3 of 9
  • Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack, photo 4 of 9
  • Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack, photo 5 of 9
  • Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack, photo 6 of 9
  • Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack, photo 7 of 9
  • Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack, photo 8 of 9
  • Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack, photo 9 of 9

Amarine Made · Vehicle & Boat Rod Holders

Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack

Check price on Amazon

As an Amazon Associate First Cast Fishing earns a commission when you buy through links on this site, at no extra cost to you.

Quick take

A pair of heavy-duty 316 stainless steel rod holders with 90-degree angled flanges and integrated drainage for gunnel mounting.

This is a pair of flush-mount rod holders cast from 316 stainless steel, set at a 90 degree angle for holding rods upright on a boat gunnel. Each has an interior liner and a drain barb so a hose can carry water out of the tube. The tube is about 9 inches long with a stop pin and fits a rod butt of roughly 1 5/8 inches inside diameter. A good fit for boat anglers who want permanent, corrosion-resistant holders built into the deck.

Best for

  • Saltwater boats
  • Permanent rod holder installation
  • Large rods and reels

Skip if

  • You need different angles
  • You want adjustable positioning

Strengths

  • Solid 316 stainless steel is corrosion-resistant
  • Heavy-duty construction lasts years
  • Integrated drain prevents water pooling

Trade-offs

  • 90-degree angle only, not adjustable
  • Fixed positioning requires correct installation
  • Drain hole adds maintenance

Fishing fit

Water
  • Saltwater
  • Freshwater

Specifications

Specifications
Typerod holder
Quantity2 holders
MaterialSolid cast 316 stainless steel
Angle90 degrees
Outer diameter2 in
Length9 in with stop pin
Mount typeFlush mount

How it compares

How this product compares with similar products on this site
Product
Amarine Made Heavy-Duty Stainless Rod Holders, 90 Degree, 2-Pack
PLUSINNO 4-Pack Fishing Rod Holders for Boat, Aluminum Dual-V DesignPick it if you need four clamp-on rod holders for one boat rail or tube and want each rod to lock at its own angle.
VEXPLO Bike Rod Holder with Adjustable Pole Mount, 2 in DiameterPick it if you ride a bike, e-bike or scooter to the water and want one light plastic rod holder with a 2-inch opening and a pin that stops the rod from dropping through.
PLUSINNO Rod Holder, Adjustable Clamp, 1.97 in Max Opening, 2-PackPick it if your boat rail or tube is up to 1.97 inches wide and you want two 360-degree holders for spinning, casting or spincast rods.
Sumind Rod Strap Holder, Elastic, 12 Inch, 4-PackPick it if you want four 12-inch rod hold-down straps for a boat or kayak deck and plan to trim the cord to your spacing.
Marinebaby Tournament Boat Rod Holders, 316 Stainless Steel, PairPick it if your boat has rails measuring 7/8 inch to 1 inch and you want 316 stainless holders with a 10 inch tube.

Updated